Sunday, 19 February 2012

Needlekeep/Pinkeep

Materials needed:
  • Stitched piece
  • Contrasting backing fabric
  • Wadding
  • Cardboard
  • Cording
  • Ribbons
  • PVA glue/a hot glue gun

IMAG1799

Step 1 ~ Front panel start

Begin by applying glue to the card and press on two layers of wadding. If using PVA glue you will need to wait for the glue to dry before continuing.

IMAG1801 IMAG1802

Step 2 ~ Front panel

Position your finished stitching over the wadding and card, glue the sides and pull the fabric over tightly then continue with the top and bottom before neatening the edges. If using PVA glue you may need to peg the sides to hold it together whilst it dries.

IMAG1803 IMAG1804

IMAG1805 IMAG1806

Step 3 ~ Reverse panel

For the reverse panel follow the same steps as the front panel with only one layer of wadding. Top, bottom, sides and neaten the corners. Again peg to gold whilst drying when using PVA.

IMAG1807 IMAG1809

IMAG1810 IMAG1811

Step 4 ~ Attach a ribbon loop

Attach a loop of ribbon. I've stuck the beginning of my cording in-between to hold on to it whilst it is glued around the edge after.

IMAG1812

Step 5 ~ Sandwich

Apply glue to both halves and then sandwich together. If using PVA you will need to either peg together as before or apply a heavy weight (maybe a stack of books) just to make sure the two sides bond.

IMAG1813

IMAG1814

Step 6 ~ Cording

Glue cording all the way around. You may need to pin in place whilst waiting for PVA glue to dry.

IMAG1815

Tuck in the end of the cording.

IMAG1816

Step 7 ~ Add a bow and Finito!

Finally the pinkeep/needlekeep is finished with a bow!

IMAG1817

Saturday, 9 July 2011

Step One ~ Circle Ornament

Materials needed:


  • Stitched design

  • Square of fabric same size

  • Cardboard

  • PVA/glue gun

  • Ribbon

  • Needle and thread

As always make sure your finished stitching is washed and pressed. Trim your stitched piece to allow enough overlap, usually upto 2 inches. Cut a square of your chosen backing fabric to the same size.


IMAG0984


All pictures are clickable if you are having trouble seeing the steps.

Step Two ~ Getting the shape

Cut 2 cardboard circles slightly bigger than the stitched design.

IMAG0408

Cut two pieces of wadding the same size as the circles and stick using PVA glue or a glue gun. Add more wadding to one circle for the front of the ornament.

IMAG0412

Step Three ~ Glueing

I've used a glue gun here but you can use PVA, you will have to apply more pressure and wait for the PVA to dry.

Fabric quare and stitched piece right-side down, place wadding side onto centre and position.

IMAG0985

Put some glue onto the cardboard and begin pulling over the excess fabric, smoothing out any bumps that may arise until you have gone all the way around.

IMAG0986 IMAG0987

IMAG0988

Do this for both pieces.

IMAG0989

Step Four ~ Sandwich

Attached a loop of ribbon to the bank piece, cover card in glue and press the front piece on top.

IMAG0990 IMAG0991

Step Five ~ Tidying Up

As the cardboard may warp when pulling the fabric smooth I like to slip stitch all the way around the edge to keep the two pieces together and neaten up the edge before adding anything else.

IMAG0992 IMAG0995

Step Six ~ Ribbon Embellishment

I've used two organza ribbons here but you can use any type of ribbon, not too wide and any colour that suite your chosen stitched piece and fabric.

Make a loop start and push the needle through the underside of the ribbon/ribbons leaving a tail of at least 10cms if starting in the bottom centre.

IMAG0996

Push the needle back through the ribbon and through both front and back.

IMAG0997

Continue all the way around pushing the ribbon close together each time.

IMAG1000

Step Seven ~ Tie a bow

Once you've gone all the way around with your ribbon leave a length of at least 10cm and end off the thread. Tie a knot in the ribbon and tie a bow. Hey Presto, Finito!!!

IMAG1001 IMAG1002

Saturday, 1 August 2009

Step One ~ All-in-One Book

Materials needed:

  • Stitched design
  • Backing fabric
  • Wadding
  • Cardboard
  • PVA glue
  • Something heavy for weight
  • Braid, pins and ribbon
  • Velcro
  • Sewing thread/sewing machine - if making the ORT bag

Have your stitched design washed and pressed. Decide how much allowance you would like around the stitched part and pull a thread from each side and top and bottom. This will leave a gap in the fabric and will be used to line up when glueing. Then trim an allowance of 2inches all the way around. - Just as you would for the Flatfold.

Photobucket

Photobucket

Cut 2 pieces of backing fabric the same size as your newly trimmed stitched piece and 1 with an extra 3 inches on one side. For the pocket cut 1 piece the same width but half the length.

Photobucket

As you can see I haven't trimmed my stitched piece as I stitched it too close to the edge of the fabric and so need all the fabric possible, lol.

Cut your cardboard into 4 equal pieces, measuring the same size as the shape created on your stitched piece.


Photobucket

Step 2 ~ front cover

Take one cardboard piece and cut 4 pieces of wadding the same size.

Photobucket

Stick the wadding to one side of the cardboard and flip over.

Photobucket

Lay your stitched design face down and place the cardboard, wadding side down, on top.



Photobucket



Glue around the edge of the cardboard and fold up the sides of the stitched fabric, pulling them inplace till the pulled threads line up.

Photobucket

Step 3 ~ other panels

No need to put wadding on the rest of the cardboard pieces. Simply use the same method as the fron cover, by placing the cardboard on the wrong side of your backing fabric panels.

Photobucket

Glue around the edges and pull the edges onto the glue. Remember to leave the longer panel with one long side open.

Photobucket

They should all look like this:

Photobucket

Step 4 ~ begin sandwiching

Add some ribbon to one side of the stitched panel and match this with the longer (open panel).

Photobucket

For the pocket, Stitch along the top edge of the panel, lay face down and place one of the backing panels face down on top. Glue around the edges and pull tight, making sure it is straight.

Begin sandwiching by gluing the back of the pocket panel and the back - longer panel and sticking them together.

Photobucket

I have added tabs to the top edge of mine. These can be created by using ribbon or in my case, strips of fabric, glued down the centre for a no seam finish.

Apply your weight and wait for it to dry.

Step 5 ~ sandwiching the front

Place the last backing fabric panel face down onto the pocket panel, fold over the longer flap and glue.

Photobucket

Glue the whole panel and line up the stitched panel facing up. Press down and apply the weight untill dry.

Photobucket